Skip to main content

Product information "Colour light signal control module "

Suitable to connect all scales of Viessmann standard colour light signals. With this module you can control the aspects of colour light signals without using relays. Optional connection of one signal with more aspects or two signals with 3 aspects. Special technology allows prototypical smooth changing of the signal lights. Optional blanking (distant signal switched off while main signal on the same mast shows “stop” position). One control module replaces up to 7 relays which are required with conventional technology. Without train control, so best used with computer-controlled digital layouts. Controlled by push-button panels items 5546 or 5547, single switch, track contacts or digital decoders are possible.

Warn- und Sicherheitshinweise

Modellbauartikel, kein Spielzeug! Nicht geeignet für Kinder unter 14 Jahren!

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Passende Artikel

Push-button panel 4-aspect

Average rating of 0 out of 5 stars

5545 Push-button panel 4-aspect
With impulse contact for two 4-aspect signals colour light, to activate the signals stop, proceed, proceed at reduced speed and stop for shunting movements by control module item 5210 as well as the control module for colour light departure signals item 5223. In analogue mode controlling with control module items 5224 and 5229, by 4-aspect signals connection. Several panels may be connected. Contact load: Up to 2 A.

€26.95*
available
Stk

Customers also bought

Push button green, 5 pieces

Average rating of 0 out of 5 stars

68302 Push button green, 5 pieces
Mounting diameter: 0,7 cm, up to 1 A.

€15.50*
available
Stk
H0 Suspended box girders covering 2 tracks

Average rating of 0 out of 5 stars

4160 H0 Suspended box girders covering 2 tracks
Equipped with tower mast, ready-to-install and varnished. With 2 electrically insulated beams. The beam components are variably adjustable. With rear side cut-out to accommodate more beams. Filigree metal work with stamped rivet imitations. Maximum span width: 11,75 cm, height: 15,09 cm.

€39.95*
available
Stk
Receiver coil for retrofitting CarMotion trucks and buses, inductive charging

Average rating of 0 out of 5 stars

8440 Receiver coil for retrofitting CarMotion trucks and buses, inductive charging
The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm

€9.95*
currently not available
Wire 0,14 mm², yellow, 25 m

Average rating of 0 out of 5 stars

68643 Wire 0,14 mm², yellow, 25 m
High-grade litz wire for low-loss current feed and signal transmission.

Content: 25 m (€0.34* / 1 m)

€8.50*
available
Stk
Locomotive cleaner, 500 ml

Average rating of 0 out of 5 stars

6856 Locomotive cleaner, 500 ml
Removes quickly grease, oil and dirt from the top-quality locomotive. Part the vehicle, remove the box and spray the cleaner and affect. Runs-off residue-free and takes away the dirt.

Content: 0.5 l (€35.90* / 1 l)

€17.95*
currently not available
H0 Weights for MB ACTROS vehicles, 3 pieces

Average rating of 0 out of 5 stars

8428 H0 Weights for MB ACTROS vehicles, 3 pieces
Weight for CarMotion MB Actros vehicles with M cab. Retrofitting ahead of the front axle. The weight increases the front axle’s downforce on the road, enabling the maneuvering of trailers through tighter radii.

€9.95*
available
Stk