5228 Relay for automatic train control, bistable, 2 x 1UM, negative switching impulse

Especially for a safe connection and current transmission.

available

The module offers an integrated digital decoder (Märklin-Motorola, NMRA-DCC) and is used to control 2 colour light signals (one home signal and one distant signal) with LEDs and a common plus pole or bulbs, provided they do not draw more than 200 mA in total. Therefore, it is suitable for all signal scales 0 up to Z (except for the Viessmann signals with multiplex-technology). It can be activated in conventional mode via the push-button panels items 5545, 5546 and 5547 or via a digital signal. It is equipped with Viessmann Signalbus and can be configured for the following applications:- 2 or several aspect colour light signal: A 2-aspect home signal with the aspects proceed and stop requires the push-button panel item 5547 (for 4 signals) or a digital address. A signal with 3 or 4 aspects with the additional aspects proceed slowly and shunting permitted requires the push-button panel item 5546 (3-aspect, 2 signals) resp. item 5545 (4-aspect, 2 signals) resp. a digital operation 2-aspect.- Distant signal or block signal: When configured as a block signal the module responds automatically to the status of the corresponding track sector. This works only in conjunction with track occupancy detectors with continuous output. Per signal sector up to 2 track sectors are required. In this mode the module changes automatically to proceed if the following sector is clear (unoccupied). If one of the two sectors is occupied, the module switches to stop. - Own distant signal or distant signal on the same mast: The signal module controls the main signal and the corresponding distant signal or the distant signal of a following main signal mounted on the same mast. In that case the distant signal will show the dark aspect when the main signal shows stop. - Interrupt track supply or switch on brake generator when stop aspect is shown: With the relay for automatic train control item 5228 the module can stop trains automatically either by interrupting the track voltage in front of the signal or – more prototypical – with the digital brake module item 5232 (Märklin Motorola) or a brake generator (for NMRA DCC). This makes it possible in both analogue and digital mode to control the track by sections.Signal with aspects stop and proceed slowly: If required you can configure the module to permit these two aspects only. In that case the module can be activated via the push-button panel item 5547 or a digital address. Regardless if the module is triggered by push buttons or track contacts the logic always assures that the red button has preference if two or more devices provide conflicting commands.

available

With impulse contact for two 3-aspect semaphore signals and also for hobby entry signals, items 4021, 4022, the signal control module item 5210 and control module for colour light entry signals item 5222. For activating the signal aspects stop, proceed, proceed at reduced speed and stop for shunting movements by control module item 5210 as well as the control module for colour light signals item 5222. Operation in analogue mode with control module items 5224 and 5229 when 3-aspect signals are connected. For 3-rail turnouts use diode item 6834. Several panels may be connected. Contact rating: Up to 2 A.

available

Maintenance free by LED lighting. To illuminate buildings, valuable monuments, advertising boards, mounting on funfair models or as stage projector. All spots are movable up-, down- and backwards. Spot box: L 0,55 x W 0,45 cm. Height: ca. 1,7 cm.

available

The welder kneels and performs his work in appropriate protective clothing. With realistic welding light by micro-LED offers authentic effect. Mounting depth: 38 mm. Perfectly matching hydraulic lift item 5131 and kibri item 38541 ARAL fuel station.

available

Catenary system for one oval track (112 cm x 76 cm), consisting of 14 masts item 4110, 12 catenary wires 19 cm of item 4142, 2 catenary wires 36 cm of item 4143 and one height marker item 4196. To use the catenary system as a power supply, the following additional items are required: Power mast item 4111, fuse holder item 4188 with fuses, and Y-wires item 4170, which ensure a reliable connection between the wires.

available