8211 H0 MEILLER Tipper semitrailer MHKS 40/2, functional model

The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm

available

In 1996, Mercedes introduced the ACTROS series in different variants. This vehicle is equipped with an M cab. Like all models of the CarMotion series, it comes with the following functions:- Charging and programming connection- Short charging times due to modern lithium polymer batteries- With a full battery and normal operation with waiting times and various speeds a runtime of approx. 4 – 6 hours, and approx. 2 hours at max. speed/full load is possible.- Easy on/off switching via a reed contact under the cab‘s roof with magnetic pointing stick or telescopic magnetic bar, item 8410- Infrared transmitter/receiver for distance control (limited compatibility with other IR systems)- Realistic braking resp. accelerating action and configurable speed due to speed-controlled motor- Free cargo area due to underfloor drive unit- Cabin lighting- Braking and reversing lights- Direction indicators right/left and warning lights controllable- Low beam / high beam light- Roof beacons (depending on type of vehicle)- Clear seethrough driver‘s cab with figure- 5-pole plug-in coupling for the connection of CarMotion trailers or semitrailers- Compatible with existing systems with contact wire or magnetic tape- Control by infrared light (IR), permanent magnets item 8431 in the road, electromagnetic stop coils and remote control item 8402- Even without mechanical guidance a short straight line reverse is possible via steering by the remote controlL 8.2 x W 3.5 x H 3.7 cm

available

The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.

available

The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine.L 500 x W 0.3 x H 0.05 cm

available

The remote control facilitates the control of the CarMotion vehicles on the layout as well as a simple configuration of the vehicle. For this purpose the remote control is directed towards the front part of the vehicle where its infrared sensors are located. Distances larger than 50 cm require a very precise alignment of the remote control with the vehicle. Under favourable conditions a distance of up to 1 m is possible. The device is designed for a local control of the vehicles – driving on sight, so to speak. It can be used to start a vehicle – even from an active stop coil – and to stop it at any time. Furthermore, it is possible to set the vehicle speed and other vehicle functions such as lighting, blinking lights etc. For these basic configurations, it is not necessary to connect the vehicle to the programming device. Moreover, the remote control complements the vehicle control via the magnet arrangement underneath the roadway – thus the user can carry out complex operations and has further options to intervene.

available

The InduktivCharger enables wireless recharging of vehicles through inductive communication. Vehicles come to a halt on the module and automatically position themselves over the charging coil, allowing charging currents to be self-regulated. These modules are particularly suitable for locations with longer dwell times, such as traffic lights or level crossings. Multiple modules can be interconnected to autonomously guide vehicles to charging positions with upcoming software updates. A control output for the motorized 2/3-way turnout, item 8448, which can also control servos, complements the capabilities. For trucks, the ratio of driving time to charging time is approximately 3 to 1, allowing for virtually unlimited driving time. The InduktivCharger can also switch vehicles with receiver coils on and off. Vehicles need to be retrofitted with the receiver coil, item 8440.Diameter charging coil: 40 mm, diameter electronics: 30 mm, height: 60 mm

currently not available