8418 Battery for MB ACTROS vehicles, 2 pieces

Lightweight, high-performance, and compact LiPo pouch cell with built-in protection electronics against overcharging, deep discharge and overcurrent (short-circuit resistant). Replacement parts for MB round bonnet and Magirus square bonnet vehicles.Nominal voltage 3.7 V, capacity 120 mAh, maximum charge and discharge current 2C (240 mA).L 24 x W 12 x H 7.5 mm

available

With this set you can retrofit your trailers and short semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.

available

Front axle fully assembled with steering arm and magnet for CarMotion trucks.Suitable vehicles: 8000, 8001, 8002, 8003, 8010, 8011, 8012, 8013, 8014, 8015, 8016, 8017, 8018, 8019, 8020, 8021, 8022, 8023, 8030, 8031, 8032, 8033, 8034, 8035, 8036, 8040, 8041, 8050, 8051, 8052, 8053, 8054, 8055, 8060, 8061, 8065, 8070, 8071, 8072, 8114, 8155, 8160L 2.2 x W 2.8 x H 1.3 cm

available

The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set.Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mmRecommended installation space (programming plug): ca. L 55 x W 5 x H 5 mmCable length to the IR LEDs: each ca. 300 mmIR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm

available

High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable.Operating voltage: 7 – 12 V DCL 4 x W 2.8 x H 1.3 cm

available

The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.

available