8460 CarMotion base module L 90.0 x W 54.0 x H 10.0 cm

Optimally suited for road widening for the use of CarMotion vehicles from Viessmann.L 18.5 x W 2 cm.

available

This side-strip with lay-by of the stone art series consists of weather resistant sediment composite. This material creates an unmatched realistic stone surface. Universally applicable. The surface of the pavement is created in concrete appearance. The area near the pavement is individually plantable. The length of the parking bay is suitable for buses to drive in and out. The installation of the InduktivCharger is possible due to the width.L 32 x W 6.6 x H 0.2 cm

currently not available

The Asphalt street from the stone art series consists of weather resistant sediment composite. This material creates an unmatched realistic stone surface. The street is flexible and can be easily cut with a knife. The street comes with 2 manhole covers and 2 canal lids. By light warming up using hot air the material gets flexible and uneven ways are possible to adjust.

currently not available

The street plates from the stone art series consist of weather resistant sediment composite. This material creates an unmatched realistic stone surface. The plates are flexible and can be easily cut with a knife. Dimensions: L 23 x W 23 cm.

available

The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set.Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mmRecommended installation space (programming plug): ca. L 55 x W 5 x H 5 mmCable length to the IR LEDs: each ca. 300 mmIR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm

available

The InduktivCharger enables wireless recharging of vehicles through inductive communication. Vehicles come to a halt on the module and automatically position themselves over the charging coil, allowing charging currents to be self-regulated. These modules are particularly suitable for locations with longer dwell times, such as traffic lights or level crossings. Multiple modules can be interconnected to autonomously guide vehicles to charging positions with upcoming software updates. A control output for the motorized 2/3-way turnout, item 8448, which can also control servos, complements the capabilities. For trucks, the ratio of driving time to charging time is approximately 3 to 1, allowing for virtually unlimited driving time. The InduktivCharger can also switch vehicles with receiver coils on and off. Vehicles need to be retrofitted with the receiver coil, item 8440.Diameter charging coil: 40 mm, diameter electronics: 30 mm, height: 60 mm

available

The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.

available

With a series of up to three magnets underneath the road stationary commands can be triggered, e. g. a speed variation or the switching of various light functions.Ø 0.4 x H 0.5 cm

few available

Turnout similar to item 8448, equipped with lateral actuation mechanisms (left, right) for manual operation. Ideal for systems controlled solely through our CarMotion remote control, item 8402, and permanent magnets, item 8431 (without wiring).

currently not available