8462 Mounting ring for CarMotion modules Ø 30 mm, 3 pieces
€10.50
Delivery time: 2-4 Werktage
Article no.: 8462
Product information "Mounting ring for CarMotion modules Ø 30 mm, 3 pieces"
Warn- und Sicherheitshinweise
Modellbauartikel, kein Spielzeug! Nicht geeignet für Kinder unter 14 Jahren!
Hersteller
Viessmann Modelltechnik GmbH
Bahnhofstr. 2 a
35116 Hatzfeld-Reddighausen
Kontakt
Passende Artikel
The InduktivCharger enables wireless recharging of vehicles through inductive communication. Vehicles come to a halt on the module and automatically position themselves over the charging coil, allowing charging currents to be self-regulated. These modules are particularly suitable for locations with longer dwell times, such as traffic lights or level crossings. Multiple modules can be interconnected to autonomously guide vehicles to charging positions with upcoming software updates. A control output for the motorized 2/3-way turnout, item 8448, which can also control servos, complements the capabilities. For trucks, the ratio of driving time to charging time is approximately 3 to 1, allowing for virtually unlimited driving time. The InduktivCharger can also switch vehicles with receiver coils on and off. Vehicles need to be retrofitted with the receiver coil, item 8440.Diameter charging coil: 40 mm, diameter electronics: 30 mm, height: 60 mm
available
This turnout is equipped with a powerful and low-noise drive featuring secure positioning achieved by a robust 10 mm motor with planetary gear. By rearranging the variable end stops, a left, right, or 3-way diversion can be selectively created. The electronics are housed compactly within the casing. The diverter can be controlled manually, via buttons/switches or our InduktivCharger, item 8408, enabling digital control capabilities. Like the vehicles, the turnout can be comfortably configured in the CarManager.
available
Turnout similar to item 8448, equipped with lateral actuation mechanisms (left, right) for manual operation. Ideal for systems controlled solely through our CarMotion remote control, item 8402, and permanent magnets, item 8431 (without wiring).
available
Customers also bought
This turnout is equipped with a powerful and low-noise drive featuring secure positioning achieved by a robust 10 mm motor with planetary gear. By rearranging the variable end stops, a left, right, or 3-way diversion can be selectively created. The electronics are housed compactly within the casing. The diverter can be controlled manually, via buttons/switches or our InduktivCharger, item 8408, enabling digital control capabilities. Like the vehicles, the turnout can be comfortably configured in the CarManager.
available
The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.
Content: 5 m (€3.70 / 1 m)
available
The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine.L 500 x W 0.3 x H 0.05 cm
Content: 5 m (€2.99 / 1 m)
available
The permanent magnet holder is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the holder can be flexibly positioned to the right of the roadway. This allows you to precisely verify whether – and at which point – the CarMotion vehicle detects and executes defined control commands. Its sturdy design enables quick setup and easy repositioning during test runs, ensuring accurate results under realistic conditions.
available
The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm
available
The IR Scanner is a locally deployed sensor unit designed to detect vehicle-specific information at defined points along the route. While vehicles are in motion, it captures relevant data in real time and makes this information immediately available to the traffic infrastructure. This enables situation-dependent control of routes, access points, and special zones – precise, automated, and efficient. Continuous data acquisition allows traffic flows to be differentiated in a targeted manner. For example, short vehicles can be preferentially guided into inner-city areas, while long vehicles or vehicle-trailer combinations are automatically routed along alternative paths. Access can also be selectively granted to specific vehicle types, such as allowing buses to enter designated stop areas while other traffic is diverted. Vehicles with a low battery charge can be directed to inductive charging zones, while vehicles with sufficient remaining charge continue without impacting traffic flow. The result is more efficient use of infrastructure while simultaneously relieving sensitive traffic areas.
currently not available