2111 H0 Pickup shoe for ROBEL 3 rail versions **discontinued**

Patented replacement pickup shoe low side car with drive unit 3 rail version items 2311 and 2316.

available

These couplers allow you to provide an easy power supply system for the entire train. The couplers are equipped completely with 2 connection cables and fit into the standard NEM 362 coupling shaft. The couplers are contact-proof and cannot be uncoupled automatically, yet easy to separate and to couple. The thin cables (0.6 mm) allow a very easy mounting. Current consumption: max. 750 mA.Contents: 3 pairs with 3 adapters each (S: norm, M: +0.3 mm and L: +0.6 mm).

available

The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set.Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mmRecommended installation space (programming plug): ca. L 55 x W 5 x H 5 mmCable length to the IR LEDs: each ca. 300 mmIR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm

available

In 1996, Mercedes introduced the ACTROS series in different variants. This vehicle is equipped with an M cab. Like all models of the CarMotion series, it comes with the following functions:- Charging and programming connection- Short charging times due to modern lithium polymer batteries- With a full battery and normal operation with waiting times and various speeds a runtime of approx. 4 – 6 hours, and approx. 2 hours at max. speed/full load is possible.- Easy on/off switching via a reed contact under the cab‘s roof with magnetic pointing stick or telescopic magnetic bar, item 8410- Infrared transmitter/receiver for distance control (limited compatibility with other IR systems)- Realistic braking resp. accelerating action and configurable speed due to speed-controlled motor- Free cargo area due to underfloor drive unit- Cabin lighting- Braking and reversing lights- Direction indicators right/left and warning lights controllable- Low beam / high beam light- Roof beacons (depending on type of vehicle)- Clear seethrough driver‘s cab with figure- 5-pole plug-in coupling for the connection of CarMotion trailers or semitrailers- Compatible with existing systems with contact wire or magnetic tape- Control by infrared light (IR), permanent magnets item 8431 in the road, electromagnetic stop coils and remote control item 8402- Even without mechanical guidance a short straight line reverse is possible via steering by the remote controlPrototype data: tanker semitrailer STA 22, capacity 37,200 l.L 17.1 x W 3.5 x H 3.9 cm

available

The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm

available

Patented replacement pickup shoe for items 2625 and 2627 cement mixer 3 rail version.

available