CarMotion
Topseller
The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm
available
With a series of up to three magnets underneath the road stationary commands can be triggered, e. g. a speed variation or the switching of various light functions.Ø 0.4 x H 0.5 cm
available
Cable for extending the EasyChain line for the InduktivCharger, item 8408. Ideally suited for lengthening the EasyChain line and connecting remote InduktivChargers. Length: 0.5 m per cable
available
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable.Operating voltage: 7 – 12 V DCL 4 x W 2.8 x H 1.3 cm
available
Like all models of the CarMotion series, the vehicle comes with the following functions:- Charging and programming connection- Short charging times due to modern lithium polymer batteries- With a full battery and normal operation with waiting times and various speeds a runtime of approx. 4 – 6 hours, and approx. 2 hours at max. speed/full load is possible.- Easy on/off switching via a reed contact under the cab‘s roof with magnetic pointing stick or telescopic magnetic bar, item 8410- Infrared transmitter/receiver for distance control (limited compatibility with other IR systems)- Realistic braking resp. accelerating action and configurable speed due to speed-controlled motor- Free cargo area due to underfloor drive unit- Cabin lighting- Braking and reversing lights- Direction indicators right/left and warning lights controllable- Low beam / high beam light- Roof beacons (depending on type of vehicle)- Clear seethrough driver‘s cab with figure- 5-pole plug-in coupling for the connection of CarMotion trailers or semitrailers- Compatible with existing systems with contact wire or magnetic tape- Control by infrared light (IR), permanent magnets item 8431 in the road, electromagnetic stop coils and remote control item 8402- Even without mechanical guidance a short straight line reverse is possible via steering by the remote controlPrototype data: MAGIRUS DEUTZ type 230 D 26 AK KHD Jupiter FlKfz 3-axle, wheelbase 3850 / 1380 mm, ZF six-speed constant-mesh gearbox, AK 6-80 four-stroke V8 Diesel motor type F8L914, performance 169 kW/230 HP, BILSTEIN recovery crane K 12500 H, fully hydraulic, max. payload 12 t, lifting height ca. 11 m.Suitable retrofit kit Sound: item 8452L 11 – 18 x W 3.2 – 4.3 x H 3.9 – 11.5 cm
available
Foil for displaying magnetic fields. Suitable for, among other things, detecting the magnetic tape, item 8430 and the permanent magnets, item 8431, beneath road surfaces. Please do not fold the foil!
Content: 0.0056 qm (€3,026.79 / 1 qm)
available
The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.
Content: 5 m (€3.59 / 1 m)
available
In 1996, Mercedes introduced the ACTROS series in different variants. This vehicle is equipped with an M cab. Like all models of the CarMotion series, it comes with the following functions:- Charging and programming connection- Short charging times due to modern lithium polymer batteries- With a full battery and normal operation with waiting times and various speeds a runtime of approx. 4 – 6 hours, and approx. 2 hours at max. speed/full load is possible.- Easy on/off switching via a reed contact under the cab‘s roof with magnetic pointing stick or telescopic magnetic bar, item 8410- Infrared transmitter/receiver for distance control (limited compatibility with other IR systems)- Realistic braking resp. accelerating action and configurable speed due to speed-controlled motor- Free cargo area due to underfloor drive unit- Cabin lighting- Braking and reversing lights- Direction indicators right/left and warning lights controllable- Low beam / high beam light- Roof beacons (depending on type of vehicle)- Clear seethrough driver‘s cab with figure- 5-pole plug-in coupling for the connection of CarMotion trailers or semitrailers- Compatible with existing systems with contact wire or magnetic tape- Control by infrared light (IR), permanent magnets item 8431 in the road, electromagnetic stop coils and remote control item 8402- Even without mechanical guidance a short straight line reverse is possible via steering by the remote controlL 8.8 x W 3.5 x H 4.5 cm
available
This practical accessory set includes a remote control, 10 meters of magnetic tape (0.5 mm), 10 permanent magnets, as well as a charger and a programming device.
available
Lightweight, high-performance, and compact LiPo pouch cells with built-in protection electronics against overcharging, deep discharge, and overcurrent (short-circuit resistant). Replacement part for MB Actros vehicles, designed for operations with the cells connected in parallel.Nominal voltage 3.7 V, capacity each 60 mAh, maximum charge and discharge current 2 C (120 mA).L 22 x W 12 x H 4.5 mm
available
Lightweight, high-performance, and compact LiPo pouch cell with built-in protection electronics against overcharging, deep discharge and overcurrent (short-circuit resistant). Replacement parts for MB round bonnet and Magirus square bonnet vehicles.Nominal voltage 3.7 V, capacity 120 mAh, maximum charge and discharge current 2C (240 mA).L 24 x W 12 x H 7.5 mm
available
The car detector recognizes the steering magnet of passing vehicles and is installed beneath the magnetic tape or conductive wire. Exclusively designed for use with the IR module item 8403, the InduktivCharger (item 8408) and the speed cameras (items 1330, 1331 and 1332).
available
This module is ideal for designing a wide variety of model scenes. It can, e. g. serve as a connecting element or a thematic intermediate segment that integrates seamlessly into a larger layout.Features include a pre-milled groove for 1 mm magnetic tape, item 8430 and breakout holes for the InduktivCharger, item 8408 or turnout, items 8445/8448.Supplied with acrylic glass panels for edging.L 90 x W 54 x H 10 cm
currently not available
The charger is specifically designed for smaller vehicles such as the Beetle, item 8090 and is optimally matched to the charging current of their batteries. It features the appropriate connector for these vehicle models.
currently not available
The charger for the trucks and buses of the Viessmann CarMotion system can be powered by any commercially available USB power supply unit or by almost any device such as PC, laptop, power bank etc. With the enclosed cable, the charger can be connected to a USB-A power supply. The charger’s plug just needs to be inserted into the socket underneath the CarMotion vehicle. An empty battery is recharged within 35 minutes. A partially discharged battery requires correspondingly less time to be recharged. The current charging status of the vehicle during the charging process is indicated by the interior lighting of the vehicle flashing in 4 steps.
available
Robust, low-noise drive unit designed for the motorization of the manually operated 2/3-way turnout (item 8445). Featuring a powerful 10 mm motor and planetary gear, it ensures secure positioning movements. By rearranging the variable end stops, a flexible creation of left, right, or 3-way turnout configurations is possible. The compact electronics are integrated into the housing. Control can be executed manually, via buttons/switches or the InduktivCharger (item 8408), enabling digital control. Like the vehicles, the drive unit can be comfortably configured in the CarManager.
currently not available
Cable for extending the EasyChain line for the InduktivCharger, item 8408. Ideally suited for lengthening the EasyChain line and connecting remote InduktivChargers. Length: 0.5 m per cable
available
This cable is designed for extending the 6-pin connector of the programming device, item 8401, or the charger, item 8400. Ideal for wiring hard-toreach modules, such as the IR Mini, item 8403.
available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 6.3 x W 2.8 x H 4.2 cm
currently not available
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles.Operating voltage: 7 – 12 V DCL 2.5 x W 2.8 x H 1.3 cm
available
The trailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 8.2 x W 2.9 x H 3.2 - 6.4 cm
available
The trailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 8.2 x W 2.9 x H 3.2 – 6.4 cm
available
The trailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 9.8 x W 3 x H 2.7 cm
available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 10.5 x B 2.7 x H 3.5 cm
currently not available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 14.4 x W 2.9 x H 4.1 cm
currently not available
The trailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 12.3 x W 3 x H 3.6 cm
available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 14.4 x W 2.9 x H 4.4 cm
currently not available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 10.5 x B 2.7 x H 3.5 cm
currently not available
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 10.9 x W 2.8 x H 4 cm
available
The trailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer:• Infrared transmitter for distance control• Braking and reversing lights• Direction indicators right/left and warning lights controllableL 9.3 x W 2.8 x H 4.2 cm
available
With this set you can retrofit your long trailers and semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles.Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.Cable length: ca. 19 cm
available
With this set you can retrofit your trailers and short semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.
available
Spur H0 CarMotion – Bewegte Fahrzeugmodelle für Ihre lebendige Modellwelt
Eine Modellbahnanlage lebt von Bewegung – nicht nur auf den Schienen, sondern auch auf den Straßen. Mit CarMotion von Viessmann wird Ihre Spur H0 Modellwelt noch realistischer und dynamischer. Die innovativen Fahrzeugmodelle fahren wie von selbst durch Ihre Miniaturlandschaft, halten an, blinken, beschleunigen sanft und folgen individuell programmierbaren Routen. So entsteht ein beeindruckend lebendiges Gesamtbild aus Schienen- und Straßenverkehr, das Ihre Anlage auf ein neues Niveau hebt.
Was ist CarMotion?
CarMotion ist ein zukunftsweisendes Carsystem für die Spur H0, das auf einem präzisen, unsichtbaren Lenksystem basiert. Die Fahrzeuge bewegen sich autonom über Ihre Straßen – ganz ohne sichtbare Führungsschlitze. Eine feine Drahtführung unter der Straßenoberfläche lenkt die Fahrzeuge mithilfe eines im Modell verbauten Lenkmagneten. Durch die integrierte Elektronik steuern sich die Autos selbstständig, realistisch und geräuscharm.
Mit CarMotion lassen sich nicht nur einfache Fahrten nachstellen, sondern auch komplexe Szenen wie Stadtverkehr, Überlandfahrten oder logistische Prozesse im Güterbereich. Perfekt für alle Modellbahner, die Bewegung lieben und ihrer Anlage mehr Tiefe verleihen möchten.
Technik trifft auf Realität: So funktioniert CarMotion
Jedes CarMotion-Fahrzeug ist mit modernster Technik ausgestattet: Akku, Fahrmotor, Lenkmagnet, Steuerplatine und Beleuchtung (Abblendlicht, Rücklicht, Blinker). Die Energieversorgung erfolgt über einen leistungsfähigen Lithium-Akku, der per Kontaktplatte oder spezieller Ladeposition in der Anlage einfach wieder aufgeladen werden kann.
Die Fahrzeuge folgen einer unterirdisch verlegten Drahtspur – völlig unsichtbar für den Betrachter. Das bedeutet: keine störenden Spurrillen, kein mechanischer Eingriff in die Fahrbahnoberfläche und maximale gestalterische Freiheit. Über Sensoren und digitale Steuerung lassen sich sogar Haltepunkte, Geschwindigkeiten und Richtungswechsel definieren.
Perfekt für moderne Modellbahner
Ob als Ergänzung zu Ihrer bestehenden H0-Anlage oder als Herzstück eines neuen Dioramas – CarMotion ist die ideale Lösung für alle, die mehr Bewegung, Technik und Emotion in ihre Modellwelt bringen möchten. Die hohe Detailtreue der Fahrzeuge, die präzise Steuerbarkeit und die Vielfalt an Szenarien machen CarMotion zu einem Highlight jeder Anlage.
Mehr Bewegung. Mehr Leben. Mehr Modellbahn.
Mit CarMotion in Spur H0 von Viessmann setzen Sie Ihre Miniaturwelt in Bewegung – und zwar nicht nur auf den Gleisen. Durch realistische Fahrzeugbewegungen, leise Technik und einfache Integration erschaffen Sie Szenen, die Ihre Besucher zum Staunen bringen. Holen Sie sich jetzt die nächste Dimension der Modellbahnwelt auf Ihre Anlage – mit CarMotion.