Accessories

This practical accessory set includes a remote control, 10 meters of magnetic tape (0.5 mm), 10 permanent magnets, as well as a charger and a programming device.

currently not available

Lightweight, high-performance, and compact LiPo pouch cells with built-in protection electronics against overcharging, deep discharge, and overcurrent (short-circuit resistant). Replacement part for MB Actros vehicles, designed for operations with the cells connected in parallel.Nominal voltage 3.7 V, capacity each 60 mAh, maximum charge and discharge current 2 C (120 mA).L 22 x W 12 x H 4.5 mm

available

Lightweight, high-performance, and compact LiPo pouch cell with built-in protection electronics against overcharging, deep discharge and overcurrent (short-circuit resistant). Replacement parts for MB round bonnet and Magirus square bonnet vehicles.Nominal voltage 3.7 V, capacity 120 mAh, maximum charge and discharge current 2C (240 mA).L 24 x W 12 x H 7.5 mm

available

The car detector recognizes the steering magnet of passing vehicles and is installed beneath the magnetic tape or conductive wire. Exclusively designed for use with the IR module item 8403, the InduktivCharger (item 8408) and the speed cameras (items 1330, 1331 and 1332).

currently not available

This module is ideal for designing a wide variety of model scenes. It can, e. g. serve as a connecting element or a thematic intermediate segment that integrates seamlessly into a larger layout.Features include a pre-milled groove for 1 mm magnetic tape, item 8430 and breakout holes for the InduktivCharger, item 8408 or turnout, items 8445/8448.Supplied with acrylic glass panels for edging.L 90.0 x W 54.0 x H 10.0 cm

currently not available

The charger is specifically designed for smaller vehicles such as the Beetle, item 8090 and is optimally matched to the charging current of their batteries. It features the appropriate connector for these vehicle models.

currently not available

The charger for the trucks and buses of the Viessmann CarMotion system can be powered by any commercially available USB power supply unit or by almost any device such as PC, laptop, power bank etc. With the enclosed cable, the charger can be connected to a USB-A power supply. The charger’s plug just needs to be inserted into the socket underneath the CarMotion vehicle. An empty battery is recharged within 35 minutes. A partially discharged battery requires correspondingly less time to be recharged. The current charging status of the vehicle during the charging process is indicated by the interior lighting of the vehicle flashing in 4 steps.

currently not available

Robust, low-noise drive unit designed for the motorization of the manually operated 2/3-way turnout (item 8445). Featuring a powerful 10 mm motor and planetary gear, it ensures secure positioning movements. By rearranging the variable end stops, a flexible creation of left, right, or 3-way turnout configurations is possible. The compact electronics are integrated into the housing. Control can be executed manually, via buttons/switches or the InduktivCharger (item 8408), enabling digital control. Like the vehicles, the drive unit can be comfortably configured in the CarManager.

currently not available

Cable for extending the EasyChain line for the InduktivCharger, item 8408. Ideally suited for lengthening the EasyChain line and connecting remote InduktivChargers. Length: 0.5 m per cable

available

This cable is designed for extending the 6-pin connector of the programming device, item 8401, or the charger, item 8400. Ideal for wiring hard-toreach modules, such as the IR Mini, item 8403.

available

With this set you can retrofit your trailers and short semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.

currently not available

Front axle fully assembled with steering arm and magnet for CarMotion trucks.Suitable vehicles: 8000, 8001, 8002, 8003, 8010, 8011, 8012, 8013, 8014, 8015, 8016, 8017, 8018, 8019, 8020, 8021, 8022, 8023, 8030, 8031, 8032, 8033, 8034, 8035, 8036, 8040, 8041, 8050, 8051, 8052, 8053, 8054, 8055, 8061, 8065, 8070, 8071, 8072, 8114, 8155, 8160L 1.5 x W 2.8 x H 1.3 cm

currently not available

High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable.Operating voltage: 7 – 12 V DCL 4 x W 2.8 x H 1.3 cm

available

Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module.Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz.Suitable vehicles: 8013, 8021, 8051, 8054, 8055, 8061, 8065, 8071, 8130, 8132, 8133.L 18 x W 8.8 x H 11.4 mm

available

Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module.Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz.Suitable vehicles: 8002, 8012, 8018, 8135.L 18 x W 8.8 x H 11.4 mm

available

Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module.Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz.Suitable vehicles: 8017, 8022, 8034, 8035, 8052, 8072.L 22.5 x W 11.2 x H 9.3 mm

currently not available

Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module.Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz.Suitable vehicles: 8019L 22.5 x W 11.2 x H 9.3 mm

available

Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module.Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz.Suitable vehicles: 8003, 8016, 8020, 8036, 8152, 8155, 8161.L 22.5 x W 11.2 x H 9.3 mm

currently not available

With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer.Contents: 8 rubber wheels, 4 rims, 2 steel axles, 4 sockets.Suitable for 2-axle trailer and semitrailer with twin tyres.

available

With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer.Contents: 6 rubber wheels, 6 rims, 3 steel axles, 6 sockets.Suitable for trailer and semitrailer with up to 3 axles and single tyres.

available

These steered axles for semitrailers are excellently suited for driving smaller radii even with longer semitrailers, without having to widen the roads very much in the curves or the semitrailers getting too far into the lane of opposite traffic. Precisely guided by ball bearing mounted cogwheel mechanism.

currently not available

With this kit you can equip your CarMotion trucks in the event that the original tyres are damaged or worn out. The tyres are characterized by good traction, smooth running and tracking stability, making them suitable for use on trailers as well.

available

Kit.The stationary loading and unloading ramp for heavy-duty trucks (Märklin 48740). also known as a rolling highway, is a permanently installed ramp solution specifically designed for the safe loading and unloading of CarMotion vehicles.This ramp provides a stable and durable means of moving CarMotion vehicles onto and off heavy transporters, ensuring smooth and reliable logistics during transportation operations.A road surface made of Vollmer Stone Art asphalt is included with the ramp, offering maximum durability and slip resistance.

currently not available

Weight for CarMotion MB Actros vehicles with M cab. Retrofitting ahead of the front axle. The weight increases the front axle’s downforce on the road, enabling the maneuvering of trailers through tighter radii.

available