Skip to main content Skip to search Skip to main navigation

Product information "Extension cable, 1 m "

This cable is designed for extending the 6-pin connector of the programming device, item 8401, or the charger, item 8400. Ideal for wiring hard-toreach modules, such as the IR Mini, item 8403.

Warn- und Sicherheitshinweise

Modellbauartikel, kein Spielzeug! Nicht geeignet für Kinder unter 14 Jahren!

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

IR Mini

Average rating of 0 out of 5 stars

8403 IR Mini
The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set.Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mmRecommended installation space (programming plug): ca. L 55 x W 5 x H 5 mmCable length to the IR LEDs: each ca. 300 mmIR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm

€35.95*
currently not available
Marking aid for permanent magnet installation

Average rating of 0 out of 5 stars

8434 Marking aid for permanent magnet installation
Marking aid for marking the locations of the permanent magnets, item 8431 at the correct spacing relative to each other, in a magnetic sequence, and with respect to magnetic tape, items 8429/8430.L 7 x W 3 x H 0.4 cm

€6.50*
available
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Stk
Receiver coil for retrofitting CarMotion trucks and buses, inductive charging

Average rating of 0 out of 5 stars

8440 Receiver coil for retrofitting CarMotion trucks and buses, inductive charging
The receiver coil enhances vehicles with inductive charging capabilities and necessary communication. It effortlessly clips onto the transmission block and is connected to the vehicle board through a two-pole plug connection. When used in conjunction with the InduktivCharger, item 8408, it enables unlimited runtime without user intervention. Vehicles can be powered on and off at inductive charging stations. The runtime-to-charging-time ratio is approximately 3:1, depending on system and vehicle conditions. Suitable for all CarMotion system vehicles without built-in receiver coils.Outer dimensions: L 2.4 x W 1.3 x H 0.27 cm

€9.95*
available
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Stk
Magnetic tape 1 mm, 5 m

Average rating of 0 out of 5 stars

8430 Magnetic tape 1 mm, 5 m
The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine. Dimensions: L 500 x W 0.3 x H 0.1 cm.

Content: 5 m (€3.50* / 1 m)

€17.50*
currently not available
Magnetic tape 0.5 mm, 5 m

Average rating of 0 out of 5 stars

8429 Magnetic tape 0.5 mm, 5 m
The self adhesive magnetic tape is polarized on its surface (south pole on top). It leads the guiding magnets of the CarMotion vehicles. Depending on the type of road, it is integrated into a prefabricated road system or built into the layout plate with the help of a surface milling machine.L 500 x W 0.3 x H 0.05 cm

Content: 5 m (€2.79* / 1 m)

€13.95*
available
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Stk
Permanent magnets, 12 pieces

Average rating of 0 out of 5 stars

8431 Permanent magnets, 12 pieces
With a series of up to three magnets underneath the road stationary commands can be triggered, e. g. a speed variation or the switching of various light functions.Ø 0.4 x H 0.5 cm

€8.50*
available
Product Quantity: Enter the desired amount or use the buttons to increase or decrease the quantity.
Stk