Level crossing with 2 barriers, powered by 2 separate underfloor drive units. Slow movement during opening and closing of the barriers. Track filling pieces, ramps and printed traffic signs are attached. Upgradable with extension set item 5103. For automatic use additional switching-tracks resp. reed contacts item 6840 are required. For double tracks even an electronic relay item 5552 is required. More connectors are available with items 5101 (2 rail version) and 5102 (3 rail version). When used with CarMotion, adjustments regarding the road width and the steepness of the ramp are necessary, as well as the installation of magnetic tape, since this product was not originally designed for CarMotion.Suitable sound module: item 5556. Length of barrier arms: ca. 4,3 cm.
The practical 12-pin plug-in rail connects up to 12 power consumers – simply by jacks for plugging in the resistors and diodes. Suitable for using with LED-floor interior lighting items 6045 – 6048. No plugs, screw terminals or soldering required. In order to make even very thin cables and litz wires pluggable, we recommend the adapter pins for rails, item 6044. Dimensions: L 3,2 x W 2,1 x H 0,7 cm.
Coach lighting with maintenance free, bright LEDs. Brightness adjustable by potentiometer. Can be used in any lighting prepared coaches of all manufacturers. By shortening the circuit board, it can be adapted to various waggon lengths. Constant power supply integrated, prepared for flicker-protection. Power supply by grinder / point unit or conducting couplers items 5048/5071. Suitable for DC, AC or digital power. Maximum power input 38 mA. Dimensions: L 25,4 x W 0,7 cm.
Signal in standard construction. Finely detailed metal mast. Authentic varnishing. Suitable for all analogue and digital systems. With base socket. Very simple mounting and wiring. With 2 LEDs, maintenance free. Signal pictures Hp0 and Hp1. Suitable control module: item 5221. Height: 7,9 cm.
The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set.Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mmRecommended installation space (programming plug): ca. L 55 x W 5 x H 5 mmCable length to the IR LEDs: each ca. 300 mmIR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm
These couplers base on the Fleischmann Profi plug-in coupling 6515 and provide power transmission up to 1 A each contact. They are also vertically self-centering, which effectively prevents unintended uncoupling (e. g. at the transition from horizontal track to a gradient). Uncoupling – even delayed uncoupling – is possible. This allows you to provide an easy power supply system for the entire train. As a result, pick-ups are not required for all coaches. This in turn reduces the load to be drawn by the locomotive. The couplers are equipped completely with 2 connection cables and fit into the standard NEM 362-coupling shaft. The thin cables (0,6 mm) allow a very easy mounting.