Commander und Lenz Ethernet Interface

  • Zu meiner Frage vorhin wegen dem LA152, habe ich eine weitere, hat schon mal jemand das Lenz USB / Ethernet Interface an den Commander angeschlossen? Das Interface ist ein ein Handregler an der Lenz Zentrale angeschalten und arbeitet wie ein Handregler, nur dass es über Wireless das iPhone als Handregler erkennt. Die Schnittstelle des Commanders sollte die Schnittstelle also auch als Handregler erkennen oder liege ich da falsch?
    Hier mal das Anschaltebild von Lenz: http://www.lenz-elektronik.com/digitalplus-pc-router.php


    Wäre super wenn das gehen würde (werde es am Wochenende mal testen), dann könnte ich mit meinem iPhone meine Loks steuern ;)

  • I am using the Lenz LI-USB interface connected directly to the LSB without using the LA 152.


    I have two methods for connecting an Android phone as a remote wireless handset for driving locomotives.


    Method 1 (the best)


    Installing on a PC RocRail open source software and on the phone installing from the Android Market the AndRoc application.


    The authors of RocRail will require a donation of 10 dollars to unlock this facility.


    Method 2


    Installing on the PC JMRI open source software and on the phone installing from the Android Market the Engine Driver - Connect to JMRI Throttle application.


    I believe TouchCab have a solution to use the Lenz Ethernet device with Apple's ITouch device as a remote wireless handset.


    John


    Here is my reply in German from the Google Translator.


    Ich bin mit dem Lenz LI-USB-Schnittstelle direkt an den LSB, ohne die LA 152 verbunden.


    Ich habe zwei Methoden für die Verbindung ein Android-Handy als Fernbedienung für mobile Endgeräte für den Antrieb Lokomotiven.


    Methode 1 (die besten)


    Installation auf einem PC RocRail Open-Source-Software und auf dem Handy installieren aus dem Android Market die AndRoc Anwendung.


    Die Autoren der RocRail erfordert eine Spende von 10 Dollar auf dieser Anlage zu entsperren.


    Methode 2


    Die Installation auf dem PC JMRI Open-Source-Software und auf dem Handy installieren aus dem Android Market der Lokomotivführer - Verbinden Sie JMRI Gas-Anwendung.


    Ich glaube, TouchCab haben eine Lösung für die Lenz-Ethernet-Gerät mit Apples ITouch Gerät verwenden als eine Remote-Wireless-Handset.


    John

    Commander with S88 Littfinski feedback for track monitoring and reed switches.


    5 amp booster connected to the CDE port.


    Lenz LI-USB interface connecting to a laptop via the LSB bus using RocRail software to drive trains manually via an Android phone.

  • Hallo John,


    da wir eine Gruppe von Modulbahner sind, wäre diese Lösung optimal, der Commander direkt beim Bahnhof und zur weiteren Steuerung das USB/Ethernet Interface um mit unseren iPhones unsere Loks zu steuern. Da wir aber noch Roco MM und Lenz LH Regler besitzen, sollte alles über die Lenz LA 152 funktionieren. Wir verwenden derzeit eine Lenz Zentrale mit Touch Cab.


    Da ich davon ausgehe, dass das Lenz Interface sich wie ein Handregler verhält, sollte es kein Problem sein es an den LSB (wie du schon geschrieben hast) anzuschließen.

  • Dear Wolfgang


    A problem I forgot to mention was that the Lenz LI-USB interface uses similar FDTI drivers to the Viessmann backup programme. Hence these will conflict if you try to run them both on the same PC.


    My solution is to use two PC's. One for the backup and one for the LI-USB.


    You may have a similar problem if the Lenz Ethernet interface uses FDTI drivers.


    John


    From Google


    Lieber Wolfgang


    Ein Problem, das ich vergaß zu erwähnen, dass die Lenz LI-USB-Schnittstelle ähnlich FDTI Treiber verwendet, um die Viessmann-Backup-Programm. Daher werden diese Konflikte, wenn Sie sie beide auf dem gleichen PC auszuführen.


    Meine Lösung ist, um zwei PCs verwenden. Ein für die Sicherung und eine für die LI-USB.


    Möglicherweise haben Sie ein ähnliches Problem, wenn der Lenz Ethernet-Schnittstelle verwendet FDTI Treiber.

    Commander with S88 Littfinski feedback for track monitoring and reed switches.


    5 amp booster connected to the CDE port.


    Lenz LI-USB interface connecting to a laptop via the LSB bus using RocRail software to drive trains manually via an Android phone.

  • Hallo John,


    ich möchte keinen PC nutzen, nur die iPhones zum steuern, somit sollte es kein Problem sein.


    I don't want to use a PC, only the iPhones to control, so there should be no problem.