Why automatic mode dont stopped when track voltage is off?

  • Hallo Vadim,


    perhaps i understand your question wrong.


    But usually the trackvoltage ist turn off, wenn there is a fail on the track.
    If all is ok you turn the voltage on. And than the automatic continue
    correctly. I mean that´s ok, absalutly.

    Viel Grüße
    Dieter Riethenauer


    Commander 1.402, seit 12.07, Fleischm.profigleise N
    Viessmann u. Uhlenbrock Schalt/Magnetartikeldekoder
    Rocco RM 10787 am LSB hinter Viessmann BM 5206,
    Viessmann Booster ECO4, Win 10- 64bit

  • Zitat von driethenauer

    Hallo Vadim,


    perhaps i understand your question wrong.


    But usually the trackvoltage ist turn off, wenn there is a fail on the track.
    If all is ok you turn the voltage on. And than the automatic continue
    correctly. I mean that´s ok, absalutly.


    No. I mean the following:
    I will explain with more details:


    1) Red status can be produced as manually, when immediate freesing mode needed or may also be caused by short.


    2)When track voltage is goes to off (red main button) under fully automatic mode,
    Commander don't wait green state and continue route executions, transmitting switching commands, loco commands,... etc, to zero output channell, indicating these doings on the screen as usual. - this is NOT CORRECT!


    3) So that, when You swith back to green, loko will starts, because loco commands - are repeated infinitly, but turnouts will remain at old position, because turnout commands were sended at zero track voltage moment and because turnout commands are not repeated - we have wrong operation of locos! They move by wrong way!


    Correct behaviour would be : when Red status occur - Commander must immediately stop any sending commands to zero voltage channel and wait green status, and then - cotinue, in aim to avoid loosing turnout commands!



    ===========
    Thanks,
    Vadim

  • Hallo Vadim,


    im Prinzip hast du Recht.
    Ich bin nicht so stark in die Technik eingestiegen wie du, und meine
    anlage ist auch wesentlich kleiner.
    Ich habe das so noch nicht beobachtet.
    Auch bin ich wie gesagt nicht der Fachmann, vielleicht kommen von irgendwem
    Erklärungshilfen ob und wie das gemacht werden kann.

    Viel Grüße
    Dieter Riethenauer


    Commander 1.402, seit 12.07, Fleischm.profigleise N
    Viessmann u. Uhlenbrock Schalt/Magnetartikeldekoder
    Rocco RM 10787 am LSB hinter Viessmann BM 5206,
    Viessmann Booster ECO4, Win 10- 64bit



  • Ok!
    Please give this information to developer's group.


    By the way, why my message about Commander 2 on base of Windows KPK was deleted?
    I think, it's a progressive way!


    ---------
    Vadim

  • Hallo vadim,


    bitte was ist windows KPK?
    Ich denke wie mir geht es vielen:???
    Die commander programme laufen jetz hervorragend bis Win 7 /Win8?
    Was anderes ist auch von den Anwender sicher nicht gefragt.
    Viessmann darf sich nich zu sehr verzweigen. 1 System das gepflegt wird
    für den Gebrauch des Anwenders ist genug.
    Bei Viessmann sind sicher noch viele Ideen in der Schublade, die dadurch gestört würden.


    Ich denke auch, dass das keine Disskusion für ein Anwenderforum ist.
    Es ist eine Entscheidung des Herstellers, die er sich sicher nicht vorschreiben lässt.
    Und daher auch keine Disskusion hier wünscht.
    Dieser vermutlichen Meinung schließe ich mich an.


    Daher betrachte ich das Thema auch hiermit für erledigt.

    Viel Grüße
    Dieter Riethenauer


    Commander 1.402, seit 12.07, Fleischm.profigleise N
    Viessmann u. Uhlenbrock Schalt/Magnetartikeldekoder
    Rocco RM 10787 am LSB hinter Viessmann BM 5206,
    Viessmann Booster ECO4, Win 10- 64bit

  • Zitat von driethenauer

    Hallo vadim,


    bitte was ist windows KPK?



    I mean, that it will be covenient to take portable computer large (more larger and more bug-free than Commander-1 screen ) dependable touch screen and PC Net-Book mainboard with Net WiFi and USB ports, portable light Windows OS, and add to it booster, video cam grabers, railroad network...etc, and place it into box with 2 wheels, joystick and 24 functional buttons.
    Then You can negotiate with Freiwald or with Roco, and use Railroad & Co or RocRail software. They much more bug-free and much more convenient for many purposes and national systems of railroads.



    I think that this way is more faster, progressive and cheaper, than the way of inventing it's own Viessmann "bi-cycle", stepping on the same rake (~trigger a backflash,~drop a brick )
    that Railroad & co stepped earlier, 10 years ago!



    ---------
    Thanks,
    Vadim.