Up-date - gone bad

  • Hello Henrik. You must do a reset. You will find how to do the reset in Tipps and Tricks
    in the points Commander Grundeinstellungen or in Reset.

  • Hello


    Thank you for the instructions. The problem is that is it rather difficult to read the screen - the text is all scrambled.


    [Blockierte Grafik: http://henriksilfverstolpe.com/PICT2739_resize.JPG-for-web-NORMAL.jpg]
    When starting op and pushing the 4 direction buttons.


    [Blockierte Grafik: http://henriksilfverstolpe.com/PICT2740_resize.JPG-for-web-NORMAL.jpg]
    After having presset the left control knob.


    [Blockierte Grafik: http://henriksilfverstolpe.com/PICT2741_resize.JPG-for-web-NORMAL.jpg]
    The final result after rebooting the Commander.


    I do not know if I am pressing the right buttons/knobs since there is no text or menues readible. I am unable to read anything.


    Any idea what to do?

  • - Zuoberst im gelben Feld steht: SYSTEM WIEDERHERSTELLEN
    - im roten Feld darunter steht:
    WELCHER MODUS SOLL AKVITIERT WERDEN? Tasten mindesten 3 Sekunden
    drücken.
    a) Im längeren weißen Feld darunter steht:
    AUSLIEFERUNGSZUSTAND AKTIVIEREN 4 RICHTUNGSTASTEN
    Wenn man die 4 Richtungstasten für mind. 3 Sekunden drückt, wird der
    Commander auf Werkseinstellung zurückgesetzt.
    - ACHTUNG: es werden alle Daten auf Werkseinstellung zurückgesetzt
    und alle benutzerspezifischen Daten werden gelöscht.
    - Wenn man die Tasten nicht so lange drückt, kommt man in das Menü
    und die eigenen Daten sind noch vorhanden. Das ist hilfreich, wenn
    sich der C aufhängt, um wieder arbeiten zu können.
    b) im weißen Feld links unten steht: UPDATEMODUS NAVIGATORCLICK
    Anstatt die 4 Richtungstasten zu drücken, muß man auf den Navigator
    klicken und man kommt in den Updatemodus.
    c) im weißen Feld rechts unten steht: VERLASSEN DREHREG. KLICK
    Wenn man den C doch nicht auf die Werkseinstellung zurücksetzen
    will, drückt man kurz auf einen der beiden Drehregler und man
    kommt zurück in das Hauptmenü.
    Wichtig:
    Um b) Updatemode auszuwählen, auf den Navigatorknopf drücken. Das sollte man
    zuerst versuchen und wenn der C sich im Updatemodus befindet, den Update vom
    PC aus nochmals starten. Wenn der C den Update nicht ausführt oder der PC eine
    Fehlermeldung bringt, dann bleibt nur, ein Reset durchzuführen.
    Dazu nochmals die Prozedur von vorne anfangen, den C starten und gleichzeitig
    die 4 Richtungstasten drücken. Wenn das Bild SYSTEM WIEDERHERSTELLEN angezeigt
    wird, die 4 Richtungstasten mindestens 3 Sekunden lang drücken. Wenn der Reset
    erfolgreich war, den C im Menü über Systemparameter in den Updatemodus setzen
    und den Update vom PC aus starten.
    --------------
    I try to translate:
    The text in the yellow zone on top is: SYSTEM WIEDERHERSTELLEN (=RESET)
    The text in the long red zone is: what kind of mode do you want to activate?
    Please press the buttons for at least 3 seconds.
    a) the text in the long white zone is: to do the reset please press the 4 direction
    buttons forward/backward for at least 3 seconds
    or b) the text in the short white zone below at the left hand side is:
    Updatemode: Navigator click
    Please press the Navigator button if you want to go into the Updatemode
    or c) the text in the short white zone below at the right hand side is:
    Return on last screen: Speed control click


    Important:
    If you want to select b) Updatemode you must click on the Navigator button. Please try
    it first and try to start the Update from your PC once more. If you cannot go back in
    the Updatemode or if your PC will not effect the Update and will have an error message,
    press again the start button and the 4 direction buttons and then you must do the
    reset with a) pressing the 4 direction buttons again for at least 3 seconds.
    If the reset is successful you must again select the Updatemode in the menu.

  • Thank you for trying to help. This is how I do it.


    1. Push the ON/OFF and let the C start.
    2. The gray/yellow page comes on - but the text is not readable.
    3. Push all 4 direction buttons for at least 3 seconds.
    4. Red bar with 3 buttons light up - the text is not readable.
    5. Push the 4 directions buttons for at least 3 secunds.
    6. I am asked to calibrate the screen and after marking the 4 corners I am asked to mark something in the middle.
    7. I move the navigation bar around and the C proceed.
    8. I end up with the screen completely full of grafics. No text.


    Am I doing right?


    I also tried to connect to UPDATE-mode, but eh PC-program just keeps staying that it does not detect any Commander (my guess - it is not in UPDATE-mode).

  • Hello. Please try first to select mode b)
    At the end, if you will be asked to calibrate the screen this is very simple. You must click on
    the 4 points on the screen and then the screen will be calibrated.
    I think you must not calibrate the screen but the navigator as follows proceeding with b):
    NAVIGATORKALIBRIERUNG
    a) Auswahl ab dem Menu:
    - Im Hauptmenü drücken auf das links-unterste Feld mit
    dem Symbol für Systemparameter
    - Im Menü EDITOREN drücken auf das Symbol
    Systemparameter hinter dem Text SYSTEMPARAMETER
    - Im Menü SYSTEMEINSTELLUNGEN tippen auf das Symbol hinter
    dem Text DISPLAY
    - Im Menü DISPLAY EINSTELLUNGEN tippen auf das Leerfeld
    hinter dem Text NAVIGATORKALIBRIERUNG
    b) Navigator Kalibrierung Fortsetzung
    Anzeige des Bildschirms, auch wenn man einen Reset durchführt:
    - Es wird ein Bild angezeigt mit einem Kreis und einem +.
    - Den Navigator auf der geriffelten Fläche an einem Punkt
    mit dem Zeigefinger anfassen und den Navigator links oder
    rechts drehen, bis 4 blaue Punkte sichtbar sind.
    - Eine der 4 Richtungstasten drücken und es wird ein 5. blauer
    Punkt im Zentrum des + sichtbar.
    - Erneut eine der 4 Richtungstasten oder den Navigator drücken.
    - Der Navigator ist kalibriert und es wird das Menü angezeigt.
    ----------english
    b) Navigator calibration continuation
    - You will find a circle and a + on the screen
    - Touch the fluted surface of the Navigator with one finger and turn it until
    you will see 4 blue points.
    - Press one of the 4 direction buttons and you will find a 5th blue point
    in the middle of the + .
    - Press again one of the 4 direction buttons or the Navigator itself.
    - The Navigator calibration was successful and the Commander Menu will be shown
    on the screen.

  • Hello Henrik. I'm glad that your C is working properly again. But one question:
    Did the C really ask you to calibrate the screen? When I did once the same procedure
    the C asked me to calibrate the Navigator.
    Best regards Udo

  • Hello Henrik. I hope that your Commander is still working. Nevertheless I tried to find an explanation why your first reset did not work correctly. Looking on your second foto with a + in a circle I see that in this case the Commander demanded a Navigator Calibration as I described it and not a display calibration. In this case you did not the right step and this is the explanation for the 3rd screen containing only nonsense. But I admit that executing a Navigator calibration without help is impossible.

    • Offizieller Beitrag

    Hello Hendrik,


    the first reset might not have been working, if you did not press the button long enough.


    If some grafic symbols e.g. the speedometer are still missing after the reset, restart the update and program the Commander again with the latest update.