Beiträge von hburg01

    Thank you for that.


    Could you please send me the link!?
    The only thing I find is the "reference handbuch", I assume you are referring to something else...


    Danke Schon


    Hans

    Mr Meier,


    I was hoping if you could still give me an answer on this?
    The same applies for the other topic on "help with blocks".


    As said in that email, I do not understand German well, and this makes the detaield help of no use to me.
    I would really like some assistance.
    Been struggling with the commander before, gave it up, and now gave it a final try, as I had heard that things had improved.
    but without help, which also says something about the usability of the product, I am stuck, and have no other option than to put it in the closet again.


    Appreciate your reply in fullest.

    Thank you for your reply, and yes you are correct. I do not have a problem with that however.
    But my first 5233 on address 0 does not work anymore, when connecting others from pos 1 and upwards.
    Not even in direct modus, and no power on the rails either.


    But like I said under the hardware ocnfiguration for the S88-Bus, I have a list on the left with an extensive list of 8- and 16-feedbacks. the first 10 are assigned as 16-modules, which I do not use.
    How can I change this? The button "Remove last decoder from list" does not do anything.
    How can I get my 5233 on address 0 to work again!?

    Hi!


    I've read the detailed help from the commander site, but still seem not to be able to get things working with my blocks/fahrstraben.
    Situation as follows:
    5233 viessman ruckmelders.
    simple single test track in an oval, station with 2 tracks. Oval contains 3 blocks, station 2.
    Each block is made of 2 ruckmelders/sections, one for breaking and one for stopping.


    I am trying to setup my fahrstrassen in such a way, that a simple block process is working. i.e. train in block 3, block 2 signal red and train to stop.
    train to drive again when block 3 is free.
    For block 1 and 2, if a train is in block 1, switches to be set so the next train goes to block 2, both to monitor track 3.



    I cannot even get the simple blocks to work, at one point the signals where moving as they should, but that does not work anymore either.
    But I've tried to enter the items to get the trains to stop if the signal is red, but no luck.


    Could anyone please give me a detailed example, what I have to enter in screens 1 to 9 for th e fahrstrassen editor for the above example!?
    That would be of great help to understand more on how it actually works. The lack fo a detailed english manual is really stopping me from progressing.


    Thanks in advance!



    Hans

    Hi!


    I've added 4 5233's to my commander using S88-bus.
    I first had only one, and connected all 8 points to 8 blocks, worked fine.
    But after adding the next 3 5233's, the 8 blocks on the 1st one are not working anymore, no power, no nothing.


    The blocks on the last 3 5233's are working fine!?
    I've tried to change the configuration of the type of ruckmelders used, under systemparameters(gerate), but there is a mixed list here of 16 and 8-blcok ruckmelders, which I cannot change.
    Is there perhaps a problem here!?


    How can I get the 1st ruckmelder to work again on address 0!?


    Thanks in advance for your answer.


    Hans

    hello!


    I am trying to make my signals switch when configuring a fahrstrassen.
    The symbol for signals is showing on the right as an option to enter a command.
    But when I click it, it dissapears and changes for a ruckmeld symbol and with no means can I change the state of a signal with my fahrstrassen.
    This used to work until I updated my software version to 1.021.


    Anmy ideas!?


    Hans